Pro Qualifier Bearings
Pro Qualifier Bearings
Anyone know the size of the spool bearings for a BPS Pro Qualifier (PQX10SSLD 4.9:1 )????
Thanks in advance
Thanks in advance
-- Salim Giacoman --
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"
- facelessnewsouth
- Pro Angler
- Posts: 1540
- Joined: Mon Feb 28, 2011 2:02 pm
- Location: Savannah, GA
Re: Pro Qualifier Bearings
Same size as the bearings for a revo series reel....can't think of the mm sizes off the top of my head...boca should have them listed on their site.
- Nitroman77
- Pro Angler
- Posts: 9983
- Joined: Mon May 09, 2005 8:10 am
- Location: saint louis/charles MO
- Contact:
Re: Pro Qualifier Bearings
3x10x4,5x11x4?
THkustoms.com
Dobyns rods
Omega custom tackle
Biospawn
seaguar
phoenix boats
Dobyns rods
Omega custom tackle
Biospawn
seaguar
phoenix boats
Re: Pro Qualifier Bearings
tks...
in the Boca Page appears only the CarbonLite in 3x10x4 and the Extreme and Jhony Morris 3x10x4,5x11x4
in the Boca Page appears only the CarbonLite in 3x10x4 and the Extreme and Jhony Morris 3x10x4,5x11x4
-- Salim Giacoman --
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"
Re: Pro Qualifier Bearings
On the P/Q, the Carblite, Patriarchs I would replace all 3 bearings, On the left side plate there is a 3x10x4, on the left side of the spool there is a 5x11x4, and on the right side plate there is a small bearing that bearing touches the spool only under load and it is a 3x8x4. On P/Q reels that I tune I pull the shields off the stock bearings and U-Sonic clean them in ACETONE and lube with TSI 301. Ceramics will only be better if U are only pitching 1/4 oz baits. With the TSI 301 lube, the bearings stay lube for a good month before U have to relube, as with Ceramics if U use Rem oil, Friction Zero, Met oil, U will have relube every 2-3 days. Plus the stock S.S. bearings make not noise like the ceramics do.
Pimp My Rod & Reel Richard W. Schmitz
Re: Pro Qualifier Bearings
Tks a lot Richard....
So if I need to replace the 3 bearings i think its too expensive for a $99 reel. I use it only for deep divers and maybe the performance gain didn't worth the $50 inversion... i will try only flushing the bearings and a internal polish
So if I need to replace the 3 bearings i think its too expensive for a $99 reel. I use it only for deep divers and maybe the performance gain didn't worth the $50 inversion... i will try only flushing the bearings and a internal polish
-- Salim Giacoman --
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"
Re: Pro Qualifier Bearings
If U are only using it for deep divers then flush the stock bearings relube with a light oil and polish the inside of the pinion gear and the spool shaft and U are good to go.
Pimp My Rod & Reel Richard W. Schmitz
Re: Pro Qualifier Bearings
tks a lot Richard...
i will do that and post coments in 2 or 3 weeks (right now the reel is in paint process)
i will do that and post coments in 2 or 3 weeks (right now the reel is in paint process)
-- Salim Giacoman --
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"
"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe"