Steez 105 LTD casting issues
Steez 105 LTD casting issues
https://youtube.com/shorts/VWqEej7-Nhk?feature=share
Got a vid here. This sound is present everytime I cast with any force. When the magnetic brake is set to higher it gets even louder and it does this throughout the entire cast.
When I set the brake to 0, it only makes the sound on the initial, most forceful part of the cast. It's hampering casting distance.
Got a vid here. This sound is present everytime I cast with any force. When the magnetic brake is set to higher it gets even louder and it does this throughout the entire cast.
When I set the brake to 0, it only makes the sound on the initial, most forceful part of the cast. It's hampering casting distance.
Long live the Jerkbait
Re: Steez 105 LTD casting issues
Sounds like a clutch yoke or spring issue. Like the pinion is not fully retracting from the spool.
Re: Steez 105 LTD casting issues
^^^I think this as well^^^
That sounds like a pinion not full disengaged from the pin and spool.
Did you do a recent service on it? Is the yoke upside down?
That sounds like a pinion not full disengaged from the pin and spool.
Did you do a recent service on it? Is the yoke upside down?
"It is like a finger pointing away to the Moon...don't concentrate on the finger, or you will miss all of that heavenly glory."
-
- TT Moderator
- Posts: 6805
- Joined: Mon Feb 28, 2011 1:56 pm
- Location: Oxford GA
Re: Steez 105 LTD casting issues
I think it's the yoke, as well. If a spring pops out of place, the yoke won't keep the pinion gear fully meshed to the spool pin.
Try not to let your mind wander. It is much too small to be outside unsupervised.
Re: Steez 105 LTD casting issues
Yeppers.hoohoorjoo wrote: ↑Thu Jul 20, 2023 7:08 pmI think it's the yoke, as well. If a spring pops out of place, the yoke won't keep the pinion gear fully meshed to the spool pin.
In this case, it's during the cast, so the pinion gear shouldn't be meshed to the spool pin. Sounds like not enough clearance of the pinion from the spool/pin.
"It is like a finger pointing away to the Moon...don't concentrate on the finger, or you will miss all of that heavenly glory."
Re: Steez 105 LTD casting issues
Yoke is in there correctly. It only goes on 1 way in this reel. Doesnt appear to be worn. Springs are lll good.dragon1 wrote: ↑Sat Jul 22, 2023 7:12 pmYeppers.hoohoorjoo wrote: ↑Thu Jul 20, 2023 7:08 pmI think it's the yoke, as well. If a spring pops out of place, the yoke won't keep the pinion gear fully meshed to the spool pin.
In this case, it's during the cast, so the pinion gear shouldn't be meshed to the spool pin. Sounds like not enough clearance of the pinion from the spool/pin.
I did notice a tab on the inductor spool holder broke off, I'm going to replace this to see if it helps.
Long live the Jerkbait
Re: Steez 105 LTD casting issues
Ah, good catch! That may be the culprit right there.hmnginmn wrote: ↑Tue Jul 25, 2023 12:20 pmYoke is in there correctly. It only goes on 1 way in this reel. Doesnt appear to be worn. Springs are lll good.dragon1 wrote: ↑Sat Jul 22, 2023 7:12 pmYeppers.hoohoorjoo wrote: ↑Thu Jul 20, 2023 7:08 pmI think it's the yoke, as well. If a spring pops out of place, the yoke won't keep the pinion gear fully meshed to the spool pin.
In this case, it's during the cast, so the pinion gear shouldn't be meshed to the spool pin. Sounds like not enough clearance of the pinion from the spool/pin.
I did notice a tab on the inductor spool holder broke off, I'm going to replace this to see if it helps.
"It is like a finger pointing away to the Moon...don't concentrate on the finger, or you will miss all of that heavenly glory."
Re: Steez 105 LTD casting issues
Confirmed. It was the plastic piece in the inductor
Long live the Jerkbait
Re: Steez 105 LTD casting issues
Perfecto!
"It is like a finger pointing away to the Moon...don't concentrate on the finger, or you will miss all of that heavenly glory."