One piece rod made into a 2 piece
One piece rod made into a 2 piece
Has anyone on this forum had a one piece baitcast rod made into a 2 piece , 50/50 split ? If so, who did the work, are you happy with the results ?, etc. I was told by a guy named Ray at Hook,line and Sinker tackle shop in Guelph,Ontario that it can not be done . I think it can , so I am sceptical of his reply. I know that there are at least two type of ferrules , the european type and north american type. Any answers would be appreciated. Thanks , forum members.
-
- Pro Angler
- Posts: 1513
- Joined: Fri May 08, 2015 11:43 pm
- Location: Gold Coast, Queensland. Australia
Re: One piece rod made into a 2 piece
Can be done with an internal ferrule slid inside the bottom half and some careful measuring and tapering of the ferrule itself to fit and about 1 cm or less left on the ferrule for eventual wear og the top section.
Some outer gusseting of the top half would be a smart option rather than just binding it like most factory rods.
Some will just scream "no" to the process and say that'll ruin the action of the blank. Its all subjective to the end user imho.
Some outer gusseting of the top half would be a smart option rather than just binding it like most factory rods.
Some will just scream "no" to the process and say that'll ruin the action of the blank. Its all subjective to the end user imho.
- Mattman
- TT Gear Crew
- Posts: 2914
- Joined: Sun Apr 24, 2005 5:26 am
- Location: Fergus Falls, MN - Otterods - Hand Crafted High Performance Fishing Rods
- Contact:
Re: One piece rod made into a 2 piece
Yes it can be done. I've turned several factory rods into 2-piece rods. I build a sleeve over ferrule.
Matt Davis
Otterods-High performance fishing rods
Otterods-High performance fishing rods
Re: One piece rod made into a 2 piece
Mattman, what would that cost me , per rod?
Re: One piece rod made into a 2 piece
Well heck look what I stumbled upon here, count me in on that as well!! also would it be possible to do a four-piece configuration Allah some of the Megabass rods I like? Would love a four-piece heavier or M/H Megabass rod
- Mattman
- TT Gear Crew
- Posts: 2914
- Joined: Sun Apr 24, 2005 5:26 am
- Location: Fergus Falls, MN - Otterods - Hand Crafted High Performance Fishing Rods
- Contact:
Re: One piece rod made into a 2 piece
That's highly variable depending on what needs to happen, if guides need to be re positioned, etc. Just off the cuff, I'd expect a minimum of $100.tditox4 wrote:Mattman, what would that cost me , per rod?
Shoot me an email if you'd like to discuss further. otterods@hotmail.com
Matt Davis
Otterods-High performance fishing rods
Otterods-High performance fishing rods
- Mattman
- TT Gear Crew
- Posts: 2914
- Joined: Sun Apr 24, 2005 5:26 am
- Location: Fergus Falls, MN - Otterods - Hand Crafted High Performance Fishing Rods
- Contact:
Re: One piece rod made into a 2 piece
Cristo wrote:Well heck look what I stumbled upon here, count me in on that as well!! also would it be possible to do a four-piece configuration Allah some of the Megabass rods I like? Would love a four-piece heavier or M/H Megabass rod
Sure. Anything is possible. Quite a bit of work. But it could be done. Doing a 3-piece would help keep the cost down.
Matt Davis
Otterods-High performance fishing rods
Otterods-High performance fishing rods
-
- Senior Angler
- Posts: 69
- Joined: Tue Jul 26, 2005 6:00 pm
Re: One piece rod made into a 2 piece
St Croix has always made 2 piece bass rods in spinning and casting models. MH, high modulus? It's in there. CTS makes blanks multi-piece in just about any style, or configuration. My 3 piece peacock bass rods are built on standard production blanks from Batson/Rainshadow.