Steez A Gears
-
- Senior Angler
- Posts: 179
- Joined: Wed May 25, 2016 7:04 am
Re: Steez A Gears
G81-4101 for 6.3:1 or H63-6301 for 7.1:1
Use stock drag with clicker pawl and spring pulled out or order the drag washers from this schematic below.
http://www.daiwa.com/us/service/manuals ... _100HL.pdf
Use stock drag with clicker pawl and spring pulled out or order the drag washers from this schematic below.
http://www.daiwa.com/us/service/manuals ... _100HL.pdf
Last edited by jjbassnforfun on Wed Aug 14, 2019 7:59 am, edited 1 time in total.
2012 Stratos 285XL 150 Etec HO
-
- Senior Angler
- Posts: 179
- Joined: Wed May 25, 2016 7:04 am
Re: Steez A Gears
After some measuring/comparing. Moding the yoke was a no go.......... But, There should be enough of the OG ZLN/Steez pinions to mod them. I have a 6.3:1 lefty ordered and access to a lathe. I'll post once I get a chance to tinker. I also have a 4.9:1 and 5.3:1 set ordered as well.jjbassnforfun wrote: ↑Mon Jul 29, 2019 5:51 pmWhy not use the stacked drag from the OG?BARRAMANIAC wrote: ↑Mon Jul 29, 2019 5:02 pmpretty sure the slot in the pinion where the yoke goes is at different heights for the steez a vs og zillion pinion. but in the og zillion range there is a main gear to match 3 out of the 4 ratios available in the steez A , 5.3:1 from the j dream , 6.3:1 and 7.1:1 I have done the mod with a 6.3:1 og zillion main gear and steez A pinion and it is nice and smooth, I removed the o rings from the main shaft and use 2 carbontex washers , one under and one in the main gear and use the steez A drag plate minus the clicker pawl and spring.jjbassnforfun wrote: ↑Sun Jul 28, 2019 5:22 amSomething we'll need to work on. I'm pulling the sleeves out of my A and see what mods the yoke may need to get the OG gears fitted. I got a tatula yoke in the bin somewhere...............BARRAMANIAC wrote: ↑Sat Jul 27, 2019 2:34 pm
I am successfully running a og zillion main gear in a steez a but have to use the steez a pinion.
I want mine to be 5.3:1 and have a set of gears order. I don't have the OEM pinion and they aren't selling them yet(for repair only). I'm thinking a Tat yoke has the similar slot location and might be mod-able to get the OG gear set installed? Its my next project after the Coastal-TW 200 drag mod...........
2012 Stratos 285XL 150 Etec HO
-
- Senior Angler
- Posts: 179
- Joined: Wed May 25, 2016 7:04 am
Re: Steez A Gears
Modified set of SS SV 5.3:1 gears are in my Steez A and set for testing. Had to use a spacer where the OG yoke slot was on the pinion as a filler. Looking for recommendations on what I could use to fill the old slot area?
I'd post pic's of the modified pinion, But they usually just disappear...........
I'd post pic's of the modified pinion, But they usually just disappear...........
2012 Stratos 285XL 150 Etec HO
-
- Elite Angler
- Posts: 200
- Joined: Fri Dec 30, 2016 3:52 pm
Re: Steez A Gears
One of my gear tooth broke in my original steez A gearing
-
- Elite Angler
- Posts: 200
- Joined: Fri Dec 30, 2016 3:52 pm
Re: Steez A Gears
Anywhere I can get a set of new steez A gears without having to order from daiwa?
-
- TT Moderator
- Posts: 6801
- Joined: Mon Feb 28, 2011 1:56 pm
- Location: Oxford GA
Re: Steez A Gears
The Tackle Trap can help with all things Daiwa.Salty Parrot wrote: ↑Sun Nov 24, 2019 10:29 amAnywhere I can get a set of new steez A gears without having to order from daiwa?
Try not to let your mind wander. It is much too small to be outside unsupervised.