Page 1 of 1

Basszone handle knobs

Posted: Fri Dec 20, 2019 1:19 pm
by iabass8
Does anybody know of any way to make these knobs work with a standard daiwa handle? I put different knobs on the basszone but want to use the knobs on another reel. The ID of the bearing used is the same but the OD is different and the height is just a hair taller. Using the bearings that came /w the knobs fit perfect. I've tried to shim these every which way and can't get them to spin freely.

Re: Basszone handle knobs

Posted: Fri Dec 20, 2019 2:15 pm
by MardukFIN
Noticed same problem. :evil: Had to use Hawgtech handle then.

Re: Basszone handle knobs

Posted: Fri Dec 20, 2019 5:27 pm
by iabass8
Ha, glad I'm not the only one. I've tried removing the shields, shimming both sides of each bearing, using 2 bearings on top or bottom, shorter screws...can't get em to work unless I loosen the heck out of the screw.

Re: Basszone handle knobs

Posted: Fri Dec 20, 2019 5:56 pm
by i_am_R2
iabass8 wrote:
Fri Dec 20, 2019 5:27 pm
Ha, glad I'm not the only one. I've tried removing the shields, shimming both sides of each bearing, using 2 bearings on top or bottom, shorter screws...can't get em to work unless I loosen the heck out of the screw.
I am not familiar with these knobs so this is a shot in the dark but maybe try those curved washers that can be found on some steez and zillion reels?

Re: Basszone handle knobs

Posted: Fri Dec 20, 2019 5:57 pm
by i_am_R2
iabass8 wrote:
Fri Dec 20, 2019 5:27 pm
Ha, glad I'm not the only one. I've tried removing the shields, shimming both sides of each bearing, using 2 bearings on top or bottom, shorter screws...can't get em to work unless I loosen the heck out of the screw.
I am not familiar with these knobs so this is a shot in the dark but maybe try those curved washers that can be found on some steez and zillion reels?

Re: Basszone handle knobs

Posted: Fri Dec 20, 2019 9:58 pm
by Slazmo
Make your own Taco washers by pressing a shim washer over a shaft of a thin screw driver.

Re: Basszone handle knobs

Posted: Sat Dec 21, 2019 7:47 am
by iabass8
Slazmo wrote:
Fri Dec 20, 2019 9:58 pm
Make your own Taco washers by pressing a shim washer over a shaft of a thin screw driver.
Where would I put them? I understand the concept but where would they go in the knobs?

Re: Basszone handle knobs

Posted: Sat Dec 21, 2019 11:13 am
by i_am_R2
Under the bearing closest to the handle, so bearing > washer > handle post

Re: Basszone handle knobs

Posted: Sat Dec 21, 2019 11:17 am
by Slazmo
Put the bent side of the washer closest to the face of the bearing also, never the two up turned edges.

And you can use them in ways such as ") (" and to really space things out, if you do need to place the open side towards the bearing face use a thin shim to cover the bearing so that it'll allow the cupped washer proper seating.

Re: Basszone handle knobs

Posted: Sun Dec 22, 2019 8:53 am
by mrpao
You could use a drop of blue lok tite to keep the screw in place once you get the play out of the knobs. Once dried it should keep the screw from backing out.

Re: Basszone handle knobs

Posted: Sun Dec 22, 2019 3:54 pm
by hoohoorjoo
mrpao wrote:
Sun Dec 22, 2019 8:53 am
You could use a drop of blue lok tite to keep the screw in place once you get the play out of the knobs. Once dried it should keep the screw from backing out.
X2, Pao is spot on. Make sure you give the thread locker time to cure and those screws should never move. A word of advice-use the purple thread lock, not the blue or red. Red is permanent, blue is medium and purple is light duty. I have had the knob posts break loose from the handle when trying to break loose the blue threadlock. I've also had the screw heads strip, so a snug-fitting screwdriver is of paramount importance.

Re: Basszone handle knobs

Posted: Sun Dec 22, 2019 4:12 pm
by iabass8
mrpao wrote:
Sun Dec 22, 2019 8:53 am
You could use a drop of blue lok tite to keep the screw in place once you get the play out of the knobs. Once dried it should keep the screw from backing out.
thought about that too but once i get the play out, the knobs dont want to spin like when you have too many shims under a bearing . once i back it out, there's play.