Zillion 10 JDM schematic
Re: Zillion 10 JDM schematic
remaining pictures
- Attachments
-
- Daiwa Zillion SV TW 1000L 05.jpg (54.22 KiB) Viewed 1826 times
-
- Daiwa Zillion SV TW 1000L 06.jpg (56.17 KiB) Viewed 1826 times
-
- Daiwa Zillion SV TW 1000L 07.jpg (55.39 KiB) Viewed 1826 times
- bronzefly
- Pro Angler
- Posts: 5036
- Joined: Wed May 16, 2007 5:21 pm
- Location: www.tackletrap.com
- Contact:
Re: Zillion 10 JDM schematic
I stand corrected upon further inspection. Please accept my apology for the oversight! You are correct on the Alphas SV TW 800(XHL) in my case, and Steez A HLC - a user manual was in fact included rather than an exploded schematic. My Steez Limited SV TW 1000HL does have a full schematic, so do my US Zillions and other US reels. Very nice photos indeed that I'm sure folks will find useful. Thank you for taking the time to share them!DrPerf wrote: ↑Wed Jul 14, 2021 7:20 pmFour JDM Zillions, one Alphas SV TW, and one Millionaire CT SV, none of which included a schematic. Everyone I have communicated with that purchased the current JDM Zillion also did not have a schematic included. There was a "user manual" in Japanese, but no schematic. Cannot speak to the U.S. domestic version of the Zillion.
As far as 'self repair' or maintenance, I disassembled each of the reels in sequence, with appropriate pictures that provide more information than a schematic.
www.tackletrap.com
facebook.com/tackletrap
facebook.com/tackletrap
-
- Pro Angler
- Posts: 1514
- Joined: Fri May 08, 2015 11:43 pm
- Location: Gold Coast, Queensland. Australia
Re: Zillion 10 JDM schematic
Any of the newer Daiwa reels that are Magseal, or those that require Magseal bearings, or monocoque frame with the proprietary tool to gain access, shimano with their spool pins that they won't sell (spool, bearing and pin as 1 part), their hydrophobic waterproof coating, AR bearings that are sold in the side plate (as 1 part number). There are ways to go about it and get the job done, but there are certain elements of how things are going that are pushing out the home servicer or repairer to go to satellite service or back to base servicing.
Edit: US executive order on right to repair has been signed, so see where it goes globally.
On another note... Look at that gear tooth profile, the tooth thickness, flank, the top and bottom land of an aluminium main gear. Be interested to see the life of them, in relation to other brands and how fine their gear designs are and how they've failed so quickly.
- Attachments
-
- Re: DrPerf
- IMG_20210715_124923.jpg (11.47 KiB) Viewed 1823 times
Re: Zillion 10 JDM schematic
Johnny A wrote: ↑Fri Jun 25, 2021 5:44 pmI wanted to check something out with my reel and disassembled it. One of the bearings dropped and a thin spacer dropped. Tried to put it back together and the reel wouldn’t reengage when I turned the handle but would when I flipped the thumbar up. Took it down and reassembled. Everything works again BUT I’m not to confident with the rebuild.
1. If I make a cast, the reel reengages, the line retrieves normally and the line doesn’t peel off with the drag tightened, everything should be okay.
2. Is there a good video guide with parts in proper placement?
Thanks
What caused my query was a shim that appeared to have dropped out of the sky and onto my repair table. Every place I looked, it didn’t seem to be the point of origin. I would place the shim where I thought it would have fallen from and eventually think I found it. I have not had any problems with the reel working. It was a trial and error process.
Now that I’ve got these pictures, I’m going to give it another go.
Thanks
Re: Zillion 10 JDM schematic
Just wanted to do a follow-up:DrPerf wrote: ↑Sat Jun 26, 2021 2:43 pmWas it the bearing and bearing collar highlighted in this picture that "dropped"?
Picture is from the disassembly of the new Zillion SV TW 1000L.
It appears that Daiwa has begun to not include schematics with the new reels,
so I take sequenced pictures as I disassemble the new reels.
Regards,
Doc
I went back in using your previously posted pics. I was off by 1 part, the shim on the retrieve gear. I had it above the anti-reverse bearing when it should have been below it. All things considered, I shouldn’t complain and you should take a bow!
Re: Zillion 10 JDM schematic
This is a “schematic” of the JDM Zillion from the Plat website that is used for ordering parts. Unfortunately, the diagram does not list the part names, only numbers.Johnny A wrote: ↑Fri Jul 30, 2021 9:29 amJust wanted to do a follow-up:DrPerf wrote: ↑Sat Jun 26, 2021 2:43 pmWas it the bearing and bearing collar highlighted in this picture that "dropped"?
Picture is from the disassembly of the new Zillion SV TW 1000L.
It appears that Daiwa has begun to not include schematics with the new reels,
so I take sequenced pictures as I disassemble the new reels.
Regards,
Doc
I went back in using your previously posted pics. I was off by 1 part, the shim on the retrieve gear. I had it above the anti-reverse bearing when it should have been below it. All things considered, I shouldn’t complain and you should take a bow!
Is “105” the shim in question?
Also, there is a shim between “35” and “36” that is not shown in the Plat schematic.
FYI, parts for the new Zillion are now available.
Regards,
Doc
- Attachments
-
- Zillion SV TW highlighted.png (117.41 KiB) Viewed 1764 times
-
- Daiwa Zillion SV TW 1000L 03.jpg (66.92 KiB) Viewed 1764 times
-
- Daiwa Zillion SV TW 1000L 02.jpg (69.8 KiB) Viewed 1764 times
Re: Zillion 10 JDM schematic
105, I have it but I had placed on top of the roller bearing, not the proper position at the bottom.DrPerf wrote: ↑Fri Jul 30, 2021 3:00 pmThis is a “schematic” of the JDM Zillion from the Plat website that is used for ordering parts. Unfortunately, the diagram does not list the part names, only numbers.Johnny A wrote: ↑Fri Jul 30, 2021 9:29 amJust wanted to do a follow-up:DrPerf wrote: ↑Sat Jun 26, 2021 2:43 pmWas it the bearing and bearing collar highlighted in this picture that "dropped"?
Picture is from the disassembly of the new Zillion SV TW 1000L.
It appears that Daiwa has begun to not include schematics with the new reels,
so I take sequenced pictures as I disassemble the new reels.
Regards,
Doc
I went back in using your previously posted pics. I was off by 1 part, the shim on the retrieve gear. I had it above the anti-reverse bearing when it should have been below it. All things considered, I shouldn’t complain and you should take a bow!
Is “105” the shim in question?
Also, there is a shim between “35” and “36” that is not shown in the Plat schematic.
FYI, parts for the new Zillion are now available.
Regards,
Doc