Chronarch MGL 151HG Gear Set...
Chronarch MGL 151HG Gear Set...
Hey guys,
I'm thinking about replacing my Chronarch 151HG gearset down to 151,
But I've noticed that the 151 uses a different worm shaft (BNT5427)
than the 151HG (BNT5438), Do I have to replace that one too or is it ok
not to?
Thanks.
I'm thinking about replacing my Chronarch 151HG gearset down to 151,
But I've noticed that the 151 uses a different worm shaft (BNT5427)
than the 151HG (BNT5438), Do I have to replace that one too or is it ok
not to?
Thanks.
Re: Chronarch MGL 151HG Gear Set...
With the faster gear ratio models they have increased the winding speed for the line lay. Since the spool is rotating faster, the faster line lay assists with line lay and helps to improve the balance on the spool. It's a small difference, but is noticeable with the XG reels.
However, going to a slower gear ratio you probably will not notice much difference in this situation.
However, going to a slower gear ratio you probably will not notice much difference in this situation.
Re: Chronarch MGL 151HG Gear Set...
Sounds good, Thank you Sir.Bantam1 wrote: ↑Thu Dec 08, 2022 5:32 amWith the faster gear ratio models they have increased the winding speed for the line lay. Since the spool is rotating faster, the faster line lay assists with line lay and helps to improve the balance on the spool. It's a small difference, but is noticeable with the XG reels.
However, going to a slower gear ratio you probably will not notice much difference in this situation.
Re: Chronarch MGL 151HG Gear Set...
Ok I got the parts today (BNT5593, BNT5595) and got them installed.
all went well except for when I rotate the handle to check if everything is ok
and instantly noticed an issue, it's like hitting a "bump" every handle turn, like a
click noise to be accurate, no resistance or anything just the click noise, gets worst
when applying slight thumb pressure on the spool while rotating the handle.
Reversed everything I did, and everything is back like the way it was.
I've replaced gear sets before and it's the first time I've encountered this issue. bad gear set maybe???
all went well except for when I rotate the handle to check if everything is ok
and instantly noticed an issue, it's like hitting a "bump" every handle turn, like a
click noise to be accurate, no resistance or anything just the click noise, gets worst
when applying slight thumb pressure on the spool while rotating the handle.
Reversed everything I did, and everything is back like the way it was.
I've replaced gear sets before and it's the first time I've encountered this issue. bad gear set maybe???
Re: Chronarch MGL 151HG Gear Set...
I fear it could be in the levelwind, maybe not everything is linking up as it should. This is a similar issue I had with a reel, ended up being in the levelwind. Maybe the HG and XG are synced up with the high speed levelwind, and the lower gear is off a bit? Maybe pushing it too hard against the edge of the levelwind worm? Just guesses, I would assume it shouldn't cause an issue. Did you try the original gears and the issue stopped?tdm wrote: ↑Fri Dec 16, 2022 6:50 pmOk I got the parts today (BNT5593, BNT5595) and got them installed.
all went well except for when I rotate the handle to check if everything is ok
and instantly noticed an issue, it's like hitting a "bump" every handle turn, like a
click noise to be accurate, no resistance or anything just the click noise, gets worst
when applying slight thumb pressure on the spool while rotating the handle.
Reversed everything I did, and everything is back like the way it was.
I've replaced gear sets before and it's the first time I've encountered this issue. bad gear set maybe???
Re: Chronarch MGL 151HG Gear Set...
That's a good point but it's kind of too late now for me to check and yes, I put the old gears back and the noise went away.DirtyD64 wrote: ↑Tue Dec 27, 2022 3:41 amI fear it could be in the levelwind, maybe not everything is linking up as it should. This is a similar issue I had with a reel, ended up being in the levelwind. Maybe the HG and XG are synced up with the high speed levelwind, and the lower gear is off a bit? Maybe pushing it too hard against the edge of the levelwind worm? Just guesses, I would assume it shouldn't cause an issue. Did you try the original gears and the issue stopped?tdm wrote: ↑Fri Dec 16, 2022 6:50 pmOk I got the parts today (BNT5593, BNT5595) and got them installed.
all went well except for when I rotate the handle to check if everything is ok
and instantly noticed an issue, it's like hitting a "bump" every handle turn, like a
click noise to be accurate, no resistance or anything just the click noise, gets worst
when applying slight thumb pressure on the spool while rotating the handle.
Reversed everything I did, and everything is back like the way it was.
I've replaced gear sets before and it's the first time I've encountered this issue. bad gear set maybe???
I called Shimano customer service, explained the situation and they told me to send the reel with the new parts installed for evaluation. The reel is on its way, and I guess we'll see.
Thanks
Re: Chronarch MGL 151HG Gear Set...
I suspect one of the replacement gears has damage. It won't be the wormshaft.
Re: Chronarch MGL 151HG Gear Set...
I finally got my reel back today, Shimano replaced the gear set and just by playing with it, everything seems
to be working fine. I haven't fully test it yet, but I'm pretty sure it's all good now.
to be working fine. I haven't fully test it yet, but I'm pretty sure it's all good now.